Plumbing 101: What You Must Have for Installing a Bathtub
Plumbing 101: What You Must Have for Installing a Bathtub
Blog Article
They are making several good annotation on the subject of How to Install a Bathtub as a whole in this great article below.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough task. If the old bathtub is easily easily accessible, the job can move immediately; if you have to open a wall to get rid of the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. Make certain you have actually certified on your own for the job and also fit trying it. Rather than employing a professional to take control of a halfway-completed job, it is much better to take into consideration employing one before you begin. Chances are you may need a specialist plumber to make tube connections.
This article will aid you mount a new tub in your bathroom if you have already purchased a brand-new bathtub and also don't need to alter the plan of your previous water pipelines.
Your devices and also product list need to make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is detach the water. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing taps can be rather troublesome due to the restricted access that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before moving on to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the tub in the required setting. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the tub until the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water system and also check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise inspect the overflow outlet and also the typical electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bath tub must wait till the bath tub has actually been used at least when as this will settle it into its last position.
Getting ready for the Installation
To start with, the supporting frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last setting.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, leading to difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, and can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill up the bathtub with water prior to securing, to permit the motion experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the ceramic tiles using waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I hope you appreciated the new page. So long as you appreciated our blog posting if you please make sure you remember to pass it around. Thanks a lot for your time. Don't forget to come by our site back soon.
Explore Now Report this page